氣力輸送

　　pneumatic conveying

　　高壓空氣噴射泵（以下簡稱倉泵）是我公司在風電管道材料輸送技術領域使用的關鍵設備。這一技術適用于鋰電池原料化工合成、垃圾焚燒飛灰輸送、電廠除灰等粉狀物料輸送，今天小編將倉泵的有關知識給大家詳細介紹下。

　　The high-pressure air jet pump (hereinafter referred to as the bin pump) is a key equipment used by our company in the field of wind power pipeline material transportation technology. This technology is suitable for the chemical synthesis of lithium battery raw materials, transportation of waste incineration fly ash, power plant ash removal and other powdered material transportation. Today, the editor will introduce the relevant knowledge of warehouse pumps in detail to everyone.

　　倉泵的工作原理

　　Working principle of warehouse pump

　　當物料進入泵體倉滿后關閉各通道，對倉泵密閉，從底部進高壓空氣經過流化裝置將倉內物料形成流態化狀態，此時，打開出粉口，高壓氣流將物料沿著封閉的管道輸送到目的地，完成輸送任務。適用于長距離、現場轉彎、攀爬等復雜情況。采用螺旋、皮帶等機械設備不便使用的場所。

　　When the material enters the pump compartment and is full, close all channels and seal the compartment pump. High pressure air enters from the bottom and passes through the fluidization device to form a fluidized state of the material in the compartment. At this time, open the powder outlet, and the high-pressure airflow will transport the material along the closed pipeline to the destination, completing the conveying task. Suitable for complex situations such as long-distance, on-site turning, climbing, etc. Places where mechanical equipment such as screws and belts are inconvenient to use.

　　倉泵設備

　　Warehouse pump equipment

　　倉泵的使用條件

　　Usage conditions of warehouse pump

　　01

　　01

　　運輸?shù)牟牧蠟楦煞鄄牧?，大多?shù)顆粒尺寸不超過2mm，密度≤2；水分含量一般應小于3%（握得緊時形成球狀，拋出時可自然松動），附著力較小。

　　The transported materials are dry powder materials, with most particle sizes not exceeding 2mm and densities ≤ 2; The moisture content should generally be less than 3% (when held tightly, it forms a spherical shape and can naturally loosen when thrown out), with low adhesion.

　　02

　　02

　　輸送設計工作溫度為0≤t≤200°C，瞬時高溫不超過250°C，環境儲存溫度為-19°C。

　　The designed working temperature for conveying is 0 ≤ t ≤ 200 ° C, with an instantaneous high temperature not exceeding 250 ° C, and an environmental storage temperature of -19 ° C.

　　03

　　03

　　工作介質是經過過濾、冷卻、脫水、干燥和清潔的壓縮空氣，配有壓縮空氣儲罐。

　　The working medium is compressed air that has been filtered, cooled, dehydrated, dried, and cleaned, and is equipped with a compressed air storage tank.

　　04

　　04

　　輸送管道的出口應配備氣體和物料分離裝置，如袋式過濾器。

　　The outlet of the conveying pipeline should be equipped with gas and material separation devices, such as bag filters.

　　05

　　05

　　輸送管道直徑大于DN100及以上，轉彎采用大直徑彎頭，需內襯陶瓷耐磨材料。

　　The diameter of the conveying pipeline is greater than DN100 and above, and large diameter elbows are used for turning, which need to be lined with ceramic wear-resistant materials.

　　06

　　06

　　操作方式為全封閉、全自動，也可手動操作。

　　The operation mode is fully enclosed, fully automatic, and can also be manually operated.

　　07

　　07

　　卸料方式為可單點卸料，亦可多點卸料。

　　The unloading method can be single point unloading or multi-point unloading.

　　倉泵設備的應用

　　Application of Warehouse Pump Equipment

　　倉泵的結構組成

　　The structural composition of the warehouse pump

　　01

　　01

　　針型進料閥:粉末入口是關閉的，沒有空氣泄漏，在閥體中形成一個壓力容器。

　　Needle type feeding valve: The powder inlet is closed and there is no air leakage, forming a pressure vessel in the valve body.

　　02

　　02

　　料位檢測:檢測閥體內的料位，當倉庫裝滿時，啟動和關閉進料閥。

　　Material level detection: Detect the material level inside the valve body, and when the warehouse is full, start and close the feeding valve.

　　03

　　03

　　倉體:容積在0.2-8m?的密閉壓力容器，耐受壓力0.8MPa，建議安裝安全閥，生產廠家具有壓力容器資格證書。

　　Warehouse body: A sealed pressure vessel with a capacity of 0.2-8m ?, capable of withstanding a pressure of 0.8MPa, must be equipped with a safety valve, and the manufacturer must have a pressure vessel qualification certificate.

　　04

　　04

　　倉底流化機構:在倉底部具有特殊的高壓流化機構，使高壓空氣進入倉體后經過該裝置形成有序的空氣布結構，讓粉體流化，并有序進入出粉管內，順暢輸送。

　　Bottom fluidization mechanism: There is a special high-pressure fluidization mechanism at the bottom of the warehouse, which allows high-pressure air to enter the warehouse and form an orderly air distribution structure through the device, making the powder fluidized and orderly entering the powder outlet pipe for smooth transportation.

　　05

　　05

　　空氣調整機構:檢測管道壓力，調整空氣壓力、流量，確保物料安全輸送。

　　Air adjustment mechanism: detects pipeline pressure, adjusts air pressure and flow rate to ensure safe material transportation.

　　06

　　06

　　出料閥:出料口閥門采用耐磨、雙板閘閥，具有密閉性能和足夠的強度、耐磨性能。

　　Discharge valve: The discharge outlet valve adopts wear-resistant, double plate gate valve, which has sealing performance and sufficient strength and wear resistance.

　　倉泵的結構組成

　　The structural composition of the warehouse pump

　　上述就是氣力輸送設備之倉泵的工作原理、使用條件及組成結構的相關知識了。本文由 倉泵   友情奉獻.更多有關的知識請點擊  http://guangda-co.com/  真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　The above is the relevant knowledge of the working principle, usage conditions, and composition structure of the bin pump in pneumatic conveying equipment. This article is a friendly contribution from Cang Pump For more related knowledge, please click http://guangda-co.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.