倉泵為啥要倉泵？咱往這看。倉泵在工作的時候先打開排氣閥，然后打開進料閥進料，把這一倉進滿以后關閉排氣閥，打開出料閥，通上氣就可以輸送了。當這一倉料送完以后再次打開進料閥，然后重復前面的過程，一倉一倉的輸送。吃到這你知道它為啥叫倉泵了嗎？

　　Why do we need a warehouse pump? Let's look over here. When the bin pump is working, first open the exhaust valve, then open the feed valve to feed in. After filling the bin, close the exhaust valve, open the discharge valve, and open the air supply to transport. After the material in this warehouse is delivered, open the feeding valve again and repeat the previous process, transporting one warehouse at a time. Do you know why it's called a compartment pump?

　　濃相除塵輸灰的流程

　　The process of dense phase dust removal and ash transportation

　　除塵輸灰的流程圖:倉泵氣力輸灰系統工藝流程為:進灰─流化、出灰─吹掃三個階段，這三個階段往復循環，達到輸灰的設計要求。

　　The process flow diagram of dust removal and ash conveying: The process flow of the pneumatic ash conveying system of the bin pump is three stages: ash feeding fluidization, ash discharging blowing, and these three stages cycle back and forth to meet the design requirements of ash conveying.

　　1.進灰階段打開插板閥（多為手動控制，平時都是打開狀態，檢修時關閉）、進料閥打開氣動止回閥等其它閥門關閉，除塵灰斗內的飛灰進入倉泵內部。進灰量是由系統程序設定好的時間和料位計去控制。設定的進灰時間到，而未達到設定的料位，或已達到設定的料位而進灰時間未到，都會自動關閉氣動止回閥，轉入流化、出灰階段。

　　1. During the ash feeding stage, open the plug valve (usually manually controlled, usually in an open state, and closed during maintenance), open the feed valve, and close other valves such as the pneumatic check valve. The fly ash in the dust removal hopper enters the interior of the bin pump. The amount of ash intake is controlled by the time and level gauge set by the system program. When the set ash feeding time is reached but the set material level is not reached, or when the set material level is reached but the ash feeding time is not reached, the pneumatic check valve will automatically close and enter the fluidization and ash discharge stage.

　　2.進氣加壓流化、出灰階段打開進氣閥、出料閥、二次氣閥組，進料閥關閉，進氣加壓，進入倉泵底部流化裝置的壓縮空氣，使倉泵內的飛灰充分流化，倉泵內飛灰邊流化邊輸送，倉泵內的壓力迅速升至輸送需求壓力。

　　2. During the stage of pressurized fluidization and ash discharge, open the intake valve, discharge valve, and secondary air valve group. Close the intake valve and pressurize the intake air. Compressed air enters the bottom fluidization device of the bin pump to fully fluidized the fly ash inside the bin pump. The fly ash inside the bin pump is transported while fluidized, and the pressure inside the bin pump quickly rises to the required conveying pressure.

　　3、吹掃階段只有出料閥和二次氣閥是打開的。這一過程主要是由時間控制，當達到系統設定的吹掃時間后依次關閉一次氣閥，二次氣閥，出料閥，然后打開排氣閥和進料閥進入進灰階段，重復上述三個階段。

　　3. During the blowing stage, only the discharge valve and secondary air valve are open. This process is mainly controlled by time. When the system's set purging time is reached, the primary air valve, secondary air valve, and discharge valve are sequentially closed. Then, the exhaust valve and feed valve are opened to enter the ash feeding stage, repeating the above three stages.

　　倉泵組成：倉泵本體由鋼板或不銹鋼板材質焊接而成，符合國家Ⅰ類壓力容器標準?；叶废路脚c倉泵對接位置的手動插板閥或氣動插板閥連接，插板閥為倉泵檢修用閥，平時處于常開狀態，只有檢修時關閉防止落料。

　　Composition of Warehouse Pump: The main body of the warehouse pump is made of welded steel plates or stainless steel plates, which comply with the national Class I pressure vessel standard. The manual or pneumatic plug valve below the ash hopper is connected to the docking position of the bin pump. The plug valve is a maintenance valve for the bin pump and is usually in a normally open state. It can only be closed during maintenance to prevent material dropping.

　　倉泵的進灰口設一個電動或者氣動進料閥，現大多使用氣動閥門。

　　The ash inlet of the bin pump is equipped with an electric or pneumatic feed valve, which is mostly used now.

　　倉泵上部裝有射頻導納料位計和壓力傳感器，供檢測倉泵內的料位和壓力時使用。

　　The upper part of the bin pump is equipped with a radio frequency admittance level gauge and a pressure sensor for detecting the level and pressure inside the bin pump.

　　倉泵下部裝有流化裝置并與壓縮空氣氣管連接。倉泵配有就地氣控箱，控制箱內電磁閥按設定好的程序驅動閥門。

　　The lower part of the warehouse pump is equipped with a fluidization device and connected to a compressed air pipe. The warehouse pump is equipped with a local pneumatic control box, and the solenoid valve inside the control box drives the valve according to the set program.

　　本文由 倉泵  友情奉獻.更多有關的知識請點擊 http://guangda-co.com/ 真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Cang Pump For more related knowledge, please click http://guangda-co.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.