一般來說三葉羅茨鼓風機，各部位間隙在20℃時的靜態理論值為：

　　1、葉輪與葉輪之間的間隙0.4-~0.5mm;

　　2、葉輪與葉殼之間的徑向間隙0.2~0.3mm;

　　3、葉輪與左、右墻板之間的軸向間隙0.3~0.4mm(左墻板間隙建議大于右墻板間隙0.05mm以上)，同步齒輪的嚙合間隙0.08~0.16mm。

　　Generally speaking, for a three-blade Roots blower, the static theoretical values of the clearances between various parts at 20℃ are as follows: 1. The clearance between impellers is 0.4-~0.5mm; 2. The radial clearance between the impeller and the casing is 0.2~0.3mm; 3. The axial clearance between the impeller and the left and right wallboards is 0.3~0.4mm (the clearance with the left wallboard must be at least 0.05mm greater than that with the right wallboard), and the meshing clearance of the synchronous gears is 0.08~0.16mm.

　　三葉羅茨風機的檢修：

　　我們認為三葉羅茨鼓風機工作間隙的調整是羅茨風機整個檢修過程中非常重要，掌握起來難度也比較大，通過分析羅茨風機的結構原理，葉輪在旋轉一周的過程中，在士45°的位置上(指葉輪壓力角與水平線成士45°角度時，兩葉輪之間的間隙是兩葉輪之間非常關鍵的間隙，

　　且有兩個+45°和兩個-45°位置，在這些位置上，兩葉輪非常大軸向剖面剛好處于相對平行狀態，因此這個角度就是調整三葉羅茨鼓風機工作間隙的非常佳位置。

　　Maintenance of three-blade Roots blower: We believe that adjusting the working clearance of a three-blade Roots blower is crucial in the entire maintenance process of Roots blowers, and it is also relatively difficult to master. By analyzing the structural principle of the Roots blower, we find that during one rotation of the impeller, at the ±45° position (referring to when the pressure angle of the impeller forms an angle of ±45° with the horizontal line), the clearance between the two impellers is the most critical one. There are two +45° and two -45° positions, at which the maximum axial cross-section of the two impellers is just in a relatively parallel state. Therefore, this angle is the optimal position for adjusting the working clearance of a three-blade Roots blower.

　　羅茨風機有下面三個方面的間隙需要在安裝時進行調整：

　　1. 主動轉子與從動轉子之間的間隙；

　　2. 主動轉子和從動轉子與機殼內表面的徑向間隙；

　　3. 主動轉子和從動轉子兩端平面與墻板軸向平面的間隙。這些間隙，一般在風機說明書中均有規定。間隙過小時，則容易發熱，而使兩轉子發生摩擦，反之，間隙過大時，則使風機的性能降低。

　　The Roots blower requires adjustments to the clearances in the following three aspects during installation: 1. The clearance between the driving rotor and the driven rotor; 2. The radial clearance between the driving rotor and the driven rotor, as well as the inner surface of the casing; 3. The clearance between the flat surfaces at both ends of the driving rotor and the driven rotor, and the axial flat surface of the wallboard. These clearances are generally specified in the blower's instruction manual. If the clearance is too small, it is prone to generate heat, causing friction between the two rotors. Conversely, if the clearance is too large, it will degrade the performance of the blower.

　　因此，風機機體內轉子與機殼部分的間隙調整，是整個安裝中的關鍵。三葉羅茨鼓風機各部分間隙調整的如何，將會直接影響機器的性能，若調整的偏差較大時，甚至?xí)a(chǎn)生機械事故。

　　Therefore, the adjustment of the clearance between the rotor and the casing within the fan body is crucial in the entire installation process. The adjustment of clearances in various parts of the three-blade Roots blower will directly affect the performance of the machine. If the adjustment deviation is significant, it may even lead to mechanical accidents.

　　本文由   羅茨鼓風機 友情奉獻.更多有關的知識請點擊  http://guangda-co.com/  真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is kindly contributed by Roots Blower. For more relevant knowledge, please visit http://guangda-co.com/ with a sincere attitude. We will provide you with comprehensive services. More relevant knowledge will be contributed to you in succession. Please stay tuned